Ebm-papst S3G500-AN33-01 Manuel d'utilisateur télécharger pdf

Operating instructions

S3G500-AN33-01

Translation of the original operating instructions

ebm-papst Mulfingen GmbH & Co. KG

Bachmühle 2

D-74673 Mulfingen

Phone +49 (0) 7938 81-0

Fax +49 (0) 7938 81-110

[email protected]

www.ebmpapst.com

CONTENTS

1. SAFETY REGULATIONS AND NOTES

11. SAFETY REGULATIONS AND NOTES

Please read these operating instructions carefully before starting to work

with the device. Observe the following warnings to prevent malfunctions

or physical damage to both property and people.

These operating instructions are to be regarded as part of this device.

If the device is sold or transferred, the operating instructions must

accompany it.

These operating instructions may be duplicated and forwarded for

information about potential dangers and their prevention.

1.1 Levels of hazard warnings

11.1 Levels of hazard warnings

These operating instructions use the following hazard levels to indicate

potentially hazardous situations and important safety regulations:

DANGER

Indicates an imminently hazardous situation which, if not

avoided, will result in death or serious injury. Compliance with

the measures is mandatory.

WARNING

Indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury. Exercise extreme

caution while working.

CAUTION

Indicates a potentially hazardous situation which, if not avoided,

may result in minor or moderate injury or damage of property.

NOTE

A potentially harmful situation can occur and, if not avoided, can

lead to property damage.

1.2 Staff qualification

11.2 Staff qualification

The device may only be transported, unpacked, installed, operated,

maintained and otherwise used by qualified, trained and authorised

technical staff.

Only authorised specialists are permitted to install the device, to carry

out a test run and to perform work on the electrical installation.

1.3 Basic safety rules

11.3 Basic safety rules

Any safety hazards stemming from the device must be re-evaluated

once it is installed in the end device.

Observe the following when working on the unit:

; Do not make any modifications, additions or conversions to the

device without the approval of ebm-papst.

1.4 Electrical voltage

11.4 Electrical voltage

; Check the electrical equipment of the device at regular intervals, refer

to chapter 6.2 Safety test.

; Replace loose connections and defective cables immediately.

DANGER

Electrical load on the device

Risk of electric shock

→ Stand on a rubber mat if you are working on an electrically

charged device.

WARNING

Terminals and connections have voltage even with a

unit that is shut off

Electric shock

→ Wait five minutes after disconnecting the voltage at all poles

before opening the device.

21.5 Safety and protective functions

21.6 Electromagnetic radiation

21.7 Mechanical movement

21.8 Emission

21.9 Hot surface

21.10 Transport

21.11 Storage

31.12 Disposal

32. PROPER USE

43. TECHNICAL DATA

43.1 Product drawing

53.2 Nominal data

53.3 Data according to ErP directive

53.4 Technical features

53.5 Mounting data

53.6 Transport and storage conditions

63.7 Electromagnetic compatibility

64. CONNECTION AND START-UP

64.1 Connecting the mechanical system

64.2 Connecting the electrical system

74.3 Connection of the cables

84.4 Factory settings

94.5 Connection screen

104.6 Checking the connections

104.7 Switch on device

104.8 Switching off the device

105. INTEGRATED PROTECTIVE FUNCTIONS

116. MAINTENANCE, MALFUNCTIONS, POSSIBLE

CAUSES AND REMEDIES

126.1 Cleaning

126.2 Safety test

Item no. 50318-5-9970 · Revision 82547 · Release 2014-05-08 · Page 1 / 12

ebm-papst Mulfingen GmbH & Co. KG · Bachmühle 2 · D-74673 Mulfingen · Phone +49 (0) 7938 81-0 · Fax +49 (0) 7938 81-110 · [email protected] · www.ebmpapst.com

1 2 3 4 5 6 ... 11 12

Operating instructions 1

Résumé du contenu

Page 1 - Operating instructions

Operating instructionsS3G500-AN33-01Translation of the original operating instructionsebm-papst Mulfingen GmbH & Co. KGBachmühle 2D-74673 Mulfinge

Page 2

Operating instructionsS3G500-AN33-01Translation of the original operating instructions4.6 Checking the connections; Make sure that the power is off (a

Page 3

Operating instructionsS3G500-AN33-01Translation of the original operating instructions6. MAINTENANCE, MALFUNCTIONS, POSSIBLECAUSES AND REMEDIESDo not

Page 4

Operating instructionsS3G500-AN33-01Translation of the original operating instructionsIf you have any other problems, contact ebm-papst.6.1 CleaningNO

Page 5

Operating instructionsS3G500-AN33-01Translation of the original operating instructionsCAUTIONIn the event of failure, there is electric voltage at the

Page 6

Operating instructionsS3G500-AN33-01Translation of the original operating instructions1.12 DisposalWhen disposing of the device, please comply with al

Page 7

Operating instructionsS3G500-AN33-01Translation of the original operating instructions3. TECHNICAL DATA3.1 Product drawingAll measures have the unit m

Page 8

Operating instructionsS3G500-AN33-01Translation of the original operating instructions3.2 Nominal dataMotor M3G112-GAPhase 3~Nominal voltage / VAC 400

Page 9

Operating instructionsS3G500-AN33-01Translation of the original operating instructions3.7 Electromagnetic compatibilityEMC interferenceimmunityAcc. to

Page 10

Operating instructionsS3G500-AN33-01Translation of the original operating instructionsNOTEWater penetration into leads or wiresWater enters at the cab

Page 11

Operating instructionsS3G500-AN33-01Translation of the original operating instructionsFig. 2: Cable routing for fans installed in upright position.The

Page 12

Operating instructionsS3G500-AN33-01Translation of the original operating instructions4.5 Connection screenNo. Conn. Designation Colour Function / ass