Ebm-papst Kickstart Manuel d'utilisateur

KickstartSetup and control software for motors with integrated drive electronics

105 Using Kickstart5.1 Getting startedWARNINGDo not operate Kickstart within an automation network where any of the Kickstart CAN or CANopen communi

115 Using Kickstart5.2 Main Screen and ToolbarThe Kickstart main screen is divided into three sections:Kickstart Main Screen Layout Menu and Toolbar

125 Using Kickstart Stop DrivesResets all drive units listed in the module area and communication between the drive and the computer back to the i

135 Using Kickstart5.4 Projects and TemplatesEverything you see in the modules and content area of Kickstart is defined in a Kickstart template or p

145 Using Kickstart .kicktpl Template FilesA Kickstart installation comes with a number of predefined projects for specific tasks, stored as .kicktpl

156 Kickstart Modules6.1 CAN InterfaceDepending on the template, different modules / module names are available, i.e. the modules do not always have

166 Kickstart ModulesInverting your filterStarting your filter with the keyword exclude will hide anything that matches the filter condition, e.g.exc

176 Kickstart ModulesExample:wait 581h,8,4b 41 60 00 ?? ?4 *,1000(waits for a status word where the highest four bits are “4”. gives up after one sec

186 Kickstart Modules6.2.1 SetupThe Setup panel is used for various configuration and simple testing tasks:NOTICEUse initial setup functions with

196 Kickstart Modules StoreStore the written parameters permanently. I.e. the CANopen device will continue to use these values after a voltage rese

2Kickstart User ManualStatus: Kickstart V1.9.40 Doc Rev 1.0.12 – 31.01.2014Copyright 2013 ebm-papstAll rights reserved. No parts of this work may

206 Kickstart Modules6.3 Motor Access / CANopen NodeDepending on the template, different modules / module names are available, i.e. the modules do

216 Kickstart Modules6.3.1 CANopen Node – Edit ModeThe Edit Mode affects the appearance and behavior of the CANopen Node module. It can be modified

226 Kickstart ModulesrangeDefines the minimum and maximum values. For example:range:0,100range:-100,100optionsUsed with type:combo. This specifies a

236 Kickstart ModulesNode MonitorYou can use the Node Monitor for a simple network overview which displays some basic information on every Node ID th

246 Kickstart Modules6.5.2 ConfigurationAfter dragging a Data Object from the Object Editor and dropping it on the configuration table, you can use

256 Kickstart Modules6.5.3 Recording DataUse the Record toolbar button to start and stop recording of all monitored data into a .csv file.To make th

266 Kickstart Modules Examples for the Value / Div ScaleScaling MethodeNormalized (Standart) FormatShorthand FormatDescriptionAutoautomatic aScale w

276 Kickstart Modules6.6 UI PanelDepending on the template, different modules / module names are available, i.e. the modules do not always have all

286 Kickstart ModulesshapeDefines the type of control will be created when the Data Object is dropped on the UI Panel canvas. Available standard shap

296 Kickstart ModulesrangeDefines the allowed range for input controls. It is only used by the slider and dial controls. Examples:range:0,100range:-1

31 About This Manual 41.1 Symbols Used 41.2 Terms Used 42 Safety 62.1 Intended Use 62.2 Safety Notices 63 Overview 74 Installation 95 Us

306 Kickstart ModulesExample UI Format DefinitionsUI Format Descriptionshape:label; updates:rA read-only label. The control’s value will be read from

316.6.4 Project and UI Files / Advanced User InterfacesAfter composing your UI Panel, you can store the user interface created using the Save Proj

32www.ebmpapst.comebm-papstSt. Georgen GmbH & Co. KGHermann-Papst-Straße 178112 St. GeorgenGermanyPhone +49 7724 81-0Fax +49 7724 81-1309info2@de.

www.ebmpapst.comebm-papstSt. Georgen GmbH & Co. KGHermann-Papst-Straße 178112 St. GeorgenGermanyPhone +49 7724 81-0Fax +49 7724 [email protected]

41 About This Manual1.1 Symbols UsedThe following symbols are used in this document:WARNINGAs defined by these operating instructions and the danger

51 About This ManualSDO Service Data ObjectCANopen SDO transfers are used for low priority reading and writing of device parameters and objects. SDO

62 Safety2.1 Intended UseThis software is intended for the commissioning and service of position drives and other motionoriented machine control uni

73 OverviewRS485 CAN-BusK4 motorKickstart softwareStart screenKickstart K4Start interfaceKickstart K5Start interfaceK5 motorKickstart is a modular PC

83 OverviewKickstart projects are made up of standard modules which are used as blocks. For example, the "CAN (USB) Interface" or "Dri

94 InstallationThe Kickstart application software is usually distributed in a .exe self extracting archive file.Double-click the .exe file to copy th